2011 Hot Products Catalog

ULTRA 250/260X OEM FUEL PUMP PRESSURE REGULATOR BLOCKOFF FITTING R&D offers a Fuel Pump Pressure Regulator Blockoff Fitting Kit which will allow the O.E.M. stock in tank fuel pressure regulator to be removed com- pletely and replaced with a billet part which is necessary when installing an aftermarket externally adjustable fuel pressure regulator. The R&D fitting is manufactured to “Deadhead” or block the port solid, however, the fitting is pre-machined and tapped and can be relief drilled to be able to install a Mikuni Super BN Series jet directly into the fitting for a small in tank restrictor jet which for fine tuning fuel pressures. *Mikuni Jet not included. Description Part No. 250/260X Fuel Pump Pressure Reg. Blockoff Fitting 811-25100 R&D ULTRA 250X/260X/300X DEEP FUEL PICKUP The R&D Deep Fuel Pickup is designed to maximize fuel volume. The stock fuel pickup is located horizontally in the gas tank three inches above the bottom of the tank. This leaves approximately 5 gallons of unusable fuel in the bottom of the tank. The R&D Deep Fuel Pickup relocates the stock fuel pickup to the bottom of the tank in a vertical position. The new positioning allows for 24 percent more riding time per tank of gas. Description Part No. R&D Ultra 250X/LX/260X/300X Deep Fuel Pick Up 801-25100 R&D UNIVERSAL HIGH PERFORMANCE HIGH VOLUME FUEL PUMP KITS FOR ULTRA 250X All R&D fuel pumps have been precision flow rate tested and charted in (LPH) liters per hour. R&D fuel pumps arrive complete with terminal connectors for both the new high performance pumps quick connect installation, as well as extra terminal connector parts for the O.E.M. pump for use when converting back to stock. The R&D quick connect terminals help make fuel pump testing easy when switching from a low pressure to a high pressure fuel pump. Description Part No. R&D 255 LPH (Liter Per Hour) 811-25255 Low Pressure Fuel Pump Kit (Performer Kit) R&D 255 LPH (Liter Per Hour) 811-25256 High Pressure Fuel Pump Kit (400hp aftermarket supercharger) R&D Fuel Pump Swedge Tool* 811-25257 *NOTE: R&D High Performance fuel pumps are .040 larger than O.E.M. Mitsubishi fuel pumps on Yamaha’s and Kawasaki’s, therefore it may be necessary to use the R&D Fuel Pump swedge tool to enlarge the fuel pump housing for easy installation. R&D UNIVERSAL FUEL PRESSURE REGULATOR Universal bypass fuel pressure regulator for carbureted or EFI fuel systems applications. Base fuel pressure is adjustable from 20 to 60 PSI with high pressure spring (installed). Ideal for carbureted and EFI bypass applications where more flow and superior pressure control are desired. R&D offers two types of fuel pressure reg- ulator set ups. Part #801-25010 will come completely assembled with #4 fittings ready for R&D custom hoses with #4 AN fittings for a nice high performance hot rod look. Part #801-25009 will have brass 3/8” to 1/4” barb 90 degree fittings installed for use with push on type hose and Otekier style clamps for security. R&D offers a high performance Coast Guard approved fuel hose that can be purchased by the foot (Part #611-27502), as well as the Otekier style clamps (Part #611-27518). The universal type bypass style regulator is capable of handling any fuel pump up to 250 GPH. Replace “Deadhead” regulator performance and experience full flow volume and steady fuel pressure. R&D offers a mounting bracket (Part #801-25011) that specifically mounts the fuel pressure regulator on top of the inner cooler. This location allows the R&D custom fuel lines to route perfectly. Description Part No. R&D Fuel Pressure 801-25010 Regulator AN Style (pictured above) Mounting Bracket for Fuel Pressure Regulator 801-25011 R&D UNIVERSAL #4 AN FUEL RETURN LINE FITTING ADAPTER KIT The R&D Universal Fuel Return Line Adapter Fitting can be installed into the top of any fuel tap assembly by finding a clear area on top of the fuel tap system large enough to install the fitting. Drill a 15/32 or #56 (.468) drill size hole and install the fitting using the kit supplied aluminum seal washer on each side of the fitting. The R&D universal fuel return fitting kit is the safest and cleanest way to properly install a fuel return to the top of any make or model fuel tap assembly. Kit comes with one #4 AN bulkhead fitting, one # 4 AN bulkhead nut, and two #4 AN 7/16" Aluminum washers. Description Part No. R&D Universal #4 AN 611-27501 Style Fuel Return Line Adapter Kit R&D ULTRA 250/260X FUEL PRESSURE GAUGE R&D offers the Autogage fuel pressure gauge gives the best reference in verifying and monitoring fuel pressure precisely on any supercharged or boosted engine. 0 to 100 psi. Description Part No. R&D Ultra 250/260X Fuel Pressure Gauge 900-02180 58 INTAKE SYSTEMS KAWASAKI 4 STROKE ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL ULTRA 250X/260X • FUEL PUMP SWEDGE TOOL FUEL PUMP