2012 Hot Products Catalog

SHOP TOOLS AND PUMP SYSTEM SERVICE TOOLS 282 Description Part No. Bearing Race and Seal Drive LS12980 BEARING RACE AND SEAL DRIVER—MASTER SET Make it easier to insert bearing race and seals without damage to race. This master set includes nine drivers to fit most standard bearings. SET INCLUDES ONE OF EACH OF THE FOLLOWING DRIVERS: DRIVER PART NO. SIZE 12610 1.565” 12620 1.750” 12630 1.965” 12640 2.325” 12710 2.470” 12650 2.555” 12690 2.830” 12700 2.995” 12970 3.180” Sea Doo Part No. A. 580/650/720/800/951 All TOOL#23 18mm spline Polaris Part No. B. Polaris ALL & long TOOL#38 reach universal 20mm spline IMPELLER HOLDER TOOL Holds spline of drive shaft for removal of impeller. A. B. Sea Doo Part No. C . GTX 4-Tec SC (22mm) TOOL#70 D. RXP/RXT (27mm) TOOL#71 IMPELLER HOLDER TOOL C. D. Sea Doo Part No. RXP/RXT (27mm) WR012-SRX SOLAS IMPELLER HOLDER TOOL Kawasaki Part No. E. 440/550-89 TOOL#24 16mm spline F. 650/750/900/1100 & TOOL#23 Ultra 250/260/300 18mm spline IMPELLER HOLDER TOOL FOR KAWASAKI E. Yamaha Part No. G. WR500, WJ650LX TOOL#27 16mm spline H. 650/701/760/1100/1200 TOOL#32 18mm spline I. GP1200R TOOL#56 20mm spline (18 tooth) SHO/FZR/FZS TOOL#53 20 mm spline (20 tooth) IMPELLER SHAFT HOLDER TOOL FOR YAMAHA G. H. I. Description Part No. 650/701 TOOL#60-3 760/800/110/1200 TOOL#61-5 DRIVE COUPLER TOOLS Use to remove drive coupler from crankshaft and sub-shaft. 3/8" HAND IMPACT TOOL SET Loosens Rusted, Frozen Nuts, Bolts and Screws. Unique design delivers over 200 ft. lbs. of Shock Torque. Can be reversed to tighten. Can also be used with impact sockets! 29200 Impact Set Includes: 29000 3/8" Impact Tool 29520 3/8" Bit Holder 29630 #1 Phillips Bit 30180 #2 Phillips Bit 29550 #3 Phillips Bit 30190 #4 Phillips Bit 30170 3/8" Straight Slot Bit Description Part No. 3/8" Hand Impact Tool Set LS29200 SUPER OUT EXTRACTOR SET A super strong extractor set made of a special hardened, shock- resistant tool steel. Works on both left and right hand threads. Super Outs cut their way straight into bolts, eliminating wedging or further tightening of frozen bolts and screws. Five extractor sizes extract 1/4” to 1/2” and larger bolts and screws. Description Part No. Super Out Extractor Set LS62900 WATCON IMPELLER PITCH GAUGES It's a known fact; not all impellers are created equal. Sometimes when impellers are mass produced, there are subtle differences that can affect performance. Use this simple tool to measure the pitch angle and blade length of each blade throughout its circumference. This enables you to make adjustments to the pitch where needed. Great for fine tuning, making minor changes or verifying pitch when sending impellers off for repair. Description Part No. 140-142mm Impellers IMP-142 144-148mm Impellers IMP-148 155-160mm Impellers IMP-160 INTAKE SYSTEMS FOUR STROKE ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL ©2012 Hot Products. All rights reserved. DS# 61-5 DS# 60-3 F.