2012 Hot Products Catalog

5 SEA DOO 4 STROKE INATKE SYSTEMS ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL SEA DOO 4-STROKE • SUPERCHARGER ©2012 Hot Products. All rights reserved. SEA DOO 215 4-TEC C3 MONSTER CHARGER WHEEL R&D’s C3 Monster Compressor Wheel for all Sea Doo 215 4 Tec engines will deliver “horsepower you can feel” with instant throttle response, improved mid range acceleration, and increased top end performance. The R&D Monster Wheel replaces the stock wheels inefficient long inducer, and 6 blade design, with a modern low profile high flow 8 blade w/splitter design with increased blade tip height. The R&D C3 Monster Wheel will deliver a solid 9.5 pounds of boost pressure with a 2.5-3 pound per minute airflow gain. The R&D C3 Monster Wheel fits directly into the O.E.M. compressor housing using a kit supplied .080” compressor case spacer for a “no modifications” bolt on and go part. The increased blade tip height allows more air to flow over the wheel thus producing more pounds of air per minute of flow. The C3 Monster Kit has proven to perform well against aftermarket kits with larger inducer housings at a fraction of the cost, making the R&D C3 Monster Kit “the most bang for the buck”. The C3 Monster works exclusively with the O.E.M. intercooler, and performs well on 91 octane pump gasoline. Boost rated at 9psi @ 8000ppm and 11psi @8500 rpm. • Better throttle response and increased horsepower • Increased boost pressure (3-4psi over stock @ 8200 rpm) • Increased airflow (2.5-3.0 pound per minute gain) • 25-30 plus horsepower increase and 2 Plus MPH Gain • Precision balanced (turbo specs .012-.027 gram inches) • Utilizes O.E.M. intercooler • 91 octane pump gas friendly • Ultra easy installation • Inexpensive horsepower upgrade for RXT / RXP NOTE: The R&D C3 Monster Compressor Wheel delivers a 2.5-3.0 pound per minute airflow gain (approximately 30 horsepower at sea level). The C3 Monster Wheel will work best in 2000 ft. plus elevations, or in ambient air temperatures of 100 plus degrees. For high altitude situations (such as Denver, Colorado) or high heat conditions (above 100 degrees), R&D sug- gests the C3-C4 range of Monster Wheels. Air density is greatly influenced by heat and altitude combinations. In conditions where the air becomes less dense, power will be lost. R&D offers a range of compressor wheels that will allow the engine tuner to compensate for air density losses with a range of compressor wheels with increased blade tip height and increased inducer sizes, all with increased air flow volumes rated in pounds per minute. NOTE: For closed course or endurance racing use using the Rotax racing E.C.U. where rpms are between 8250 and 8500, R&D recommends the use of X model or aftermarket intercooler system. Tests have proven the O.E.M. intercooler to have restrictions at 23.5 pounds of air, or 9.5 pounds of boost at sea level and 60-80 degrees. Description Part No. Sea Doo 215 4-Tec C3 Monster Charger Wheel 613-94003 SEA DOO 215 4-TEC C5 MONSTER CHARGER WHEEL R&D’s C5 Monster Compressor Wheel Kit for all Sea Doo 215 4 Tec engines will deliver 40 “X” type horsepower to the 2004-2008 RXT/RXP Sea Doo’s to significantly increase overall performance. The R&D Monster Wheel Kit replaces the stock wheels inefficient long inducer, and 6 blade design, with a modern low profile high flow 8 blade w/splitter design with a 2mm larger inducer and increased blade tip height. The R&D C5 Monster Wheel Kit will deliver a solid 11 plus pounds of boost pressure with a 4 pound per minute airflow gain. The R&D C5 Monster Wheel fits directly into a kit supplied O.E.M. “X” front compressor housing using a .080” compressor case spacer for a “no modifications” bolt on power upgrade kit. The increased inducer size and blade tip height allows more air to flow over the wheel thus producing more pounds of air flow per minute. The C5 Monster will require the use of the “X”, or aftermarket intercooler kits, and performs well on 91 octane pump gasoline. Boost rated at 11psi@8000rpm and 13psi@8500rpm. • Better throttle response and increased horsepower • Increased boost pressure (4-5psi over stock @ 8200 rpm) • Increased airflow (4.0 pound per minute gain) • 40 plus horsepower increase and 3 Plus MPH Gain • Precision balanced (turbo specs .012-.027 gram inches) • Utilizes O.E.M. “X” or Aftermarket Intercooler Kits • 91 octane pump gas friendly • Ultra easy installation • Inexpensive horsepower upgrade for RXT / RXP NOTE: The R&D C5 Monster Compressor Wheel delivers a 3.75-4 pound per minute airflow gain (approximately 35-40 horsepower at sea level). The C5 Monster Wheel Kit will work best in 3000 ft. plus elevation situations (such as Denver, Colorado) or high heat conditions (above 100 degrees) with the O.E.M. intercooler. For sea level use with rpm’s over 8100 and the C5 Monster Wheel Kit, R&D strongly suggests that the “X” or aftermarket intercooler kits be used as high boost pressures and high air volumes will dead head into the O.E.M. intercooler causing compressor surge. For closed course or endurance racing use using the Rotax racing E.C.U. where rpms are between 8250 and 8500, R&D recommends the use of the X model or aftermarket intercooler system. Tests have proven the O.E.M. intercooler to have restrictions at 23.5 pounds of air, or 9.5 pounds of boost at sea level and 60-80 degrees. NOTE: Air density is greatly influenced by heat and altitude combinations. In conditions where the air becomes less dense, horsepower will be lost. R&D offers a range of compressor wheels that will allow the engine tuner to compensate for air density losses with a range of compressor wheels with increased blade tip height and increased inducer sizes, all with increased air flow volumes rated in pounds per minute. Description Part No. Sea Doo 215 4-Tec C5 Monster Charger Wheel 613-94005