2013 Hot Products Catalog

10 ©2013 Hot Products. All rights reserved. INTAKE SYSTEMS SEA-DOO 4 STROKE ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL SEA-DOO 4-STROKE • SUPERCHARGER R&D RXP/RXP-X/RXT/RXT-X GTX-SC SUPERCHARGER SURGE PROTECTOR KIT The R&D Surge Protector Kit will significantly improve supercharger clutch and compressor wheel performance and reliability by eliminating compressor surge. Compressor surge is defined as the negative charge of pressure that causes turbulence in the supercharger that occurs during aggressive of off-throttle operations. When the throttle valve is abruptly closed at high rpms, the engine decelerates quickly down from 8,000 rpms, however the supercharger is compressing air (creating boost) as the supercharger has to decelerate from 42,000 rpms. This turbulence is the primary cause of undue stress on the supercharger clutch system and its components. The R&D surge protection kit utilizes an automotive vacuum assisted Bosch pressure blow off valve that automatically releases the unwanted intake pressure between the closed throttle valve and the supercharger. As soon as the throttle valve is opened, the blow off valve immediately closes and the compressor can supply its full boost potentials to the engine. Manufactured from high-temperature silicone hose with an integrated molded riser for the blow off valve to function without hindering intake flow or velocity. The R&D kit Installs easily in place of the OEM rubber intake elbow joint. This kit is a very necessary and cost effective up-grade for all Sea-Doo supercharged watercraft. Kit comes completely assembled with silicone elbow, blow off valve, R&D B.O.V. filter, mounting hardware and instructions. Description Part No. A. R&D RXP 215, RXT 215, 613-95003 GTX-SC SC Surge Protector Kit B. R&D RXP-X 255, RXT-X 255 613-95255 SC Surge Protector Kit C. R&D RXP-X 260, RXT-X 260, 613-95258 GTR 215 SC Surge Protector Kit A. Sea-Doo 260 C. R&D/TIAL 50MM SURGE PROTECTOR R&D now offers the Ultimate Sea-Doo Surge Protector Kit. The new R&D/Tial 50mm kit works in the same fashion as our entry level surge kit, except its flow capacity is greatly increased. The 50mm diameter with its 6 exit port design releases compressor surge much quicker and more efficiently than any other system available. This means less wear and stress on the supercharger clutch. Compressor surge is defined as the negative charge of pressure that causes turbulence in the supercharger that occurs during aggressive of off-throttle operations. When the throttle valve is abruptly closed at high rpms, the engine decelerates quickly down from 8,000 rpms, however the supercharger is compressing air (creating boost) as the super- charger has to decelerate from 42,000 rpms. This turbulence is the primary cause of undue stress on the supercharger clutch system and its components. The R&D surge protection kit utilizes an automotive vacuum assisted pressure blow off valve that automatically releases the unwanted intake pressure between the closed throttle valve and the supercharger. As soon as the throttle valve is opened, the blow off valve immediately closes and the compressor can supply its full boost potentials to the engine. The R&D kit installs into the OEM intake hose, but for optimum performance, use the R&D Straight Shot Intake Hose (Pt. #613-95257). This kit is a very necessary and cost effective up-grade for all Sea-Doo supercharged watercraft. Kit comes complete with mounting hardware and instructions. For easy vacuum line hook-up use R&D Multi-Port Adaptor (Pt. #613-95270). Description Part No. D. R&D/Tial 50mm BOV Valve only 613-95263 E. R&D/Tial 50mm BOV Kit 613-95259 Valve only BOV Kit R&D MULTI-PRESSURE PORT BOOST GUAGE/SURGE/RRFPR ADAPTOR KIT The R&D Sea-Doo Multi-Pressure Port Adaptor Kit will allow quick and easy “BOLT ON” installations of Rising Rate Fuel Pressure Regulators, Tial/Greddy type surge valves, as well as digital or manual boost/vacuum gauges. The R&D Multi-Pressure Port Adaptor installs smartly between the OEM Map Sensor and the Sea-Doo intake manifold as a “bolt on” part with no drilling modifications. The R&D adapter has two large volume ports that allow for proper installation and operation of a vacuum/boost gauge, surge protection valve, and boost referenced fuel pressure regulator (RRFRP) all at the same time with one simple part. The R&D Pressure Port Adaptor Kit comes complete with all mounting hardware and instructions. Description Part No. R&D Multi-Pressure Port Boost 613-95270 Guage/Surge/RRFPR Adaptor Kit D. E. B. Sea-Doo 255 Sea-Doo 215