2013 Hot Products Catalog

106 INTAKE SYSTEMS STAND-UP PWC ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL ©2013 Hot Products. All rights reserved. KAWASAKI 1100/1200 SXR CONVERSION BULLETT RACING LIGHTWEIGHT SXR HOOD Bullett’s lightweight SXR hood is extremely strong and very durable all while coming in 12lbs lighter than a OEM Kawasaki SXR hood. The hood is predrilled for installation of the OEM hardware and utilizes the OEM hood seal. Feature additional clearance for installation of a Factory pipe. Gloss gel coated finish. Description Part No. Bullett Racing Lightweight SXR Hood-Black HOOD-KB-BLK Bullett Racing Lightweight SXR Hood-White HOOD-KB-WHT BULLETT RACING CARBON FIBER RIDE PLATE Bullett’s ride plate will improve overall speed & handling of your water- craft making your riding experience the best possible. Carbon compressed molded to retain the plate shape and design and not bend like aluminum ride plates. Improves lean angle, straight line tracking and overall grip Description Part No. Bullett Racing 800 SXR Carbon Fiber Ride Plate RP-KAW BULLETT RACING V1 HULL Bullett Racing V1-Wideboy Kawasaki SXR with molded tubbies. This boat has the same look and feel as the Original SXR with the exception of the molded tubbies for more straightline stability for greater rider input. Bullett Racing only uses the highest quality materials on the market, all of our composite products are built with AME 6000 Pure Epoxy Vinyl Ester resins. The hull comes with a composite deck and bottom, composite bulkhead, carbon fiber ride plate for rigidity and memory retension, composite hood with four air intake tubes inside the hood, tucked high up in the hood making it the most water tight hood on the market. The hull also comes with bow eyes front and rear, 2.5 inch exhaust, hull extensions, bond flange wedges, steering cable tube, 2ea. 1/2 inch water lines, 5/8 inch trim cable tube, and motor mount holes pre-drilled for either 800 or 1100 motor configuration. And last of all deck and bottom are glued together with a high strength bonding glue, and the entire hull is pre-finished on the inside with white gel-coat and black splatter. Description Part No. Bullett Racing SXR V1 Hull BUL-K1101 Bullett Racing X-2 Sport Hull with V1 Bottom BUL-K1103-1 BULLETT RACING V2 WIDEBOY HULL Bullett Racing V2-WideBoy Kawasaki SXR with molded tubbies. This boat may have the same look as the Original SXR with the exception of the bottom. The Bottom on the V2 is a race bred and proven design that over the past few years has been winning championships on every continent. This Hull was built around the intake system of this boat with no compromises in race conditions. The Wideboy hull introduces a wider tray for more rider input, the tray is 2" wider at the back and 3" wider at the front. Bullett Racing only uses the highest quality materials on the market, all of the composite products are built with AME 6000 Pure Epoxy Vinyl Ester resins. The hull comes with a composite deck and bottom, composite bulkhead, carbon fiber ride plate for rigidity and memory retension, Bullett racing proprietary intake system that comes with intake shoe and intake grate, composite hood with four air intake tubes inside the hood, tucked high up in the hood making it he most water tight hood on the market. The hull also comes with bow eyes front and rear, 2.5 inch exhaust, hull extensions, bond flange wedges, steering cable tube, 2ea.1/2 inch water lines, 5/8 inch trim cable tube, motor mount holes pre-drilled for either 800 or 1100 motor configuration. And last of all deck and bottom are glued together with a high strength bonding glue, and the entire hull is pre-finished on the inside with white gel-coat and black splatter. Description Part No. Bullett Racing V2 Race Hull Standard Deck BUL-K1102-1 Bullett Racing V2 Race Hull Wideboy Deck BUL-K1102-2 Bullett Racing X-2 Sport Hull with V2 Bottom BUL-K1103-2 Rob Flores Bullett Racing V2-Wideboy Bullett Racing X-2 Sport Hull