2013 Hot Products Catalog

181 FOUR STROKE INTAKE SYSTEMS ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL ©2013 Hot Products. All rights reserved. R&D’S “BIG ASS” PROP WRENCH R&D's Big Ass prop wrench takes the fight out of removing any tough to remove prop. Changing the prop at the beach without a vise is no prob- lem. Also light enough to carry in your luggage while traveling to interna- tional races. The key is LEVERAGE! The 28” long wrenches are made from ?” plate aluminum and utilize an ID hex to get maximum bite without slipping on the prop tool. With these tools your prop changing headaches are over, guaranteed. Measure your existing spline tool and Solas or Skat-Trak prop tool and order the proper size wrenches. Description Part No. Fits Skat-Trak Prop Tool for Super Jet/Raider/Blaster 132-56001 Hex size .875” Fits Solas Shaft Spline Tool for Super Jet 132-56002 Hex size .910” Fits Skat-Trak Prop Tool for 132-56003 SHO/FZR/FZS/GPR/HO/FX/VX Hex size 1.000” Fits R&D Shaft Spline Tool for SHO/FZR/FZS 132-56004 Hex size 1.125” Fits Solas Shaft Spline Tool for GPR 132-56005 Hex size 1.150” Fits Solas Tool 1.175” 132-56006 Hex size 1.175” Fits Solas Prop Tool for SHO/FZ 132-56007 Hex size 1.415” SOLAS STAINLESS STEEL YAMAHA 12-VANE STATOR SECTION Get HUGE gains in Hook Up on bottom end, and overall efficiency in rough conditions, and jet wash! This pump is a must have for Freestyle! The Brand New Solas Yamaha 144mm 12 Vane Pump Stator is now available and is an incredible value for the HUGE performance gain resulting from bolting this pump on! This is the stator section only, is stainless steel, with large diameter bearing carrier, and a 12 vane standard position design. It replaces the stock Yamaha 144mm 6 vane aluminum stator section. No need to buy an expensive extended shaft with this pump conversion. You will need a large hub design impeller such as the Impros Hooker impeller, the Solas Concord YQ-CD, or Skat-Trak C+75 Swirl impeller with this pump. Yamaha Part No. Stainless Steel Yamaha 12-Vane Stator YQS-SV-144 A. Impros Pump Spacer IMYQ-NS (required when Solas pump stator is used with stock nozzle) B. Impros Freestyle Tail Cone IMYQ-FC WSM Yamaha Pump Bearing & Seal Kit 003-630 A. SOLAS 12-VANE PERFORMANCE PUMP FOR KAWASAKI The Solas Kawasaki High Performance 12 Vane Pump is a stainless steel vane, 140mm diameter with 75mm bearing carrier, pressed into an aluminum housing. It is a "Standard Position" pump, meaning, it is not set back, and you can use your existing driveshaft (no extended shaft necessary). It comes complete with bearings, seals, pump shaft, and tail cone and to top it off, an adjustable diameter drop nozzle system! The pump fits the 2003-2012 Kawasaki 800 SXR. It also fits the 1992-2002 750 models SX, SXi, SXi Pro, SS, ST, Xi, and XiR. This pump kit does not include an impeller, trim system cable, or lever, we suggest using either the Solas KP-DF impeller, or the Skat-Trak C-75 Magnum Swirl impeller. These pumps really improve rough water performance, and they fit right up to the hull like an OEM pump. Description Part No. Solas 12 Vane Performance Pump KPS-PM-140/74T with Trim System for Kawasaki B.