2013 Hot Products Catalog

187 ©2013 Hot Products. All rights reserved. ALUMINUM PUMP SHOES FOR YAMAHA SUPERJET Aluminum pump shoes are designed to replace the stock plastic unit which is prone to fail with a winged intake grate. These aluminum pump shoes have a completely redesigned front entrance compared to the OEM plastic pump shoe allowing water to feed into the pump more efficiently. Improves hookup, cornering, stability, rough water speed and overall handling. Description Part No. Blowsion Yamaha SuperJet 96+ 02-02-432 Pump Intake Shoe. (Drilling is Required) Jet Dynamics SuperJet 96+ OEM Replacement JD #36 Aluminum Pump Ring Jet Dynamics Yamaha 155mm Pump Shoe JD#155 JD #36 RIVA SEA-DOO RXP/RXT/GTX-SC BILLET PUMP WEDGE 2-Degree wedge trims up your pump nozzle raising the bow of your craft for less drag and more control. Description Part No. RXP, RXP-X, RXT-X, GTS-SC RS23050-1-ER 2-Degree Pump Wedge RIVA RXP/RXP-X/RXT-X VTS EXTENSION ROD RIVA’s precision-machined VTS Extension Rod allows maximum “nozzle down” adjustment after installation of RIVA Pump Wedge. Necessary on modified craft to keep bow down during initial acceleration while still providing maximum top speed advantage when trimmed up. Adjustable design comes preset for RIVA 2° Pump Wedge (part# RS23050). Description Part No. RXP/RXP-X/RXT-X VTS Extension Rod RS23050-1-ER R&D ULTRA 250/300 1 DEGREE NOZZLE WEDGE KIT The R&D 1 Degree Reduction Nozzle Wedge Kit for the Ultra 250X/LX will add quicker acceleration and top speed performance as well as allow the bow to ride slightly higher which will significantly reduce annoying bow spray promoting a much dryer ride. Extensive testing has led our development team to wedge the reduction nozzle up 1 full degree which will inexpensively give better handling everywhere and provide a boost of up to 1 mph in top speed performance. The billet aluminum CNC machined 1 degree reduction nozzle wedge kit was specifically designed to work without compromising or removing the O.E.M. reverse gate. The R&D Pump Wedge Kit comes complete with all the necessary hardware and instructions for easy installation. Description Part No. R&D Ultra 250X/LX 1° Nozzle Wedge Kit 141-25001 R&D Ultra 300X/LX 1° Nozzle Wedge Kit 141-30000 SEA-DOO RXT 2.5 DEGREE NOZZLE WEDGE KIT The R&D 2.5 degree reduction nozzle wedge kit for the new Sea-Doo 4-TEC was designed, developed and tested extensively in all types of flat and rough water conditions to ensure that there would be no handling performance compromises. Most brands of watercraft have some form of V.T.S. (variable trim system) including other model Sea-Doo's. Why the 4-TEC doesn't have a trim system is a mystery. Extensive testing has led our development team to wedge the reduction nozzle up 2.5 degrees which will inexpensively give your 4-TEC better handling everywhere and provide a boost of 1 to 2 mph in top speed performance. The billet aluminum CNC machined 2.5 degree reduction nozzle wedge kit was designed to work with the OEM O.P.A.S. system and installs easily in 15 to 20 minutes with R&D's "easy install" directions. Description Part No. 02-03 GTX 4-TEC SC / 03-05 GTX 4-TEC NA 143-95002 2.5 Degree Pump Wedge/Cable Extension Kit RXP 215 2.5 Degree Pump Wedge/ 143-95003 Cable Extender Kit RXT 215/(04-05) GTX 4-TEC 143-95004 2.5 Degree Pump Wedge/Cable Extender Kit RXT-X 255 2.5 Degree Pump Wedge/ 143-95005 Adjustable Trim Rod/Cable Extender Kit RXP-X 255 1.0 Degree Pump Wedge/ 143-95006 Adjustable Trim Rod/Cable Extender Kit GTX 4-TEC FOUR STROKE INTAKE SYSTEMS ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL 02-02-432 RICKTER PLASTIC PUMP SHOE 144mm Pump Shoe. Fits all Rickter, SuperJet, Wave Blaster and aftermarket hulls. Replaces OEM #6R7-5311-00. Description Part No. Rickter Plastic Pump Shoe PL-P-SHOE-144