2013 Hot Products Catalog

R&D ULTRA 250X/260X/150/12F/15F BILLET DRIVE COUPLERS Billet aluminum drive coupler set for the Kawasaki 250X & 260X. The crank side coupler with the pulley is 1.24lbs lighter than the stock steel coupler. The pulley diameter is the same as stock. Uses the stock rubber dampener. Clear anodized for protection against saltwater corrosion. These couplers do not fit the Ultra 300X. Description Part No. Ultra 250X/260X Billet Drive Coupler Set 31-700590 Ultra 150/12F/15F Billet Drive Coupler Set 31-700490 R&D ULTRA 250X/260X SUPERCHARGER WHEEL PULLER TOOL The R&D wheel puller tool makes it fast and easy to remove a supercharger wheel without the removal of the intercooler system or the water muffler assembly. The R&D Supercharger drive wheel puller will save at least an hour on a pulley removal and replacement. A must have tool. Description Part No. R&D Ultra 250X/260X SC Wheel Puller Tool 611-26004 R&D ULTRA 250X/260X DRIVER WHEEL HOLDER TOOL The R&D Holding Tool makes it fast and easy to remove and re-install a supercharger wheel without damaging or breaking the wheel hub. Use the holding tool to properly torque the drive bolts and main spline drive bolt. A must have tool. Description Part No. Ultra 250X/260X Driver Wheel Holder Tool 611-26003 31-700590 76 INTAKE SYSTEMS KAWASAKI 4 STROKE ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL ULTRA 250/260/300 • SUPERCHARGER COMPONENTS & TOOLS ©2013 Hot Products. All rights reserved. R&D ULTRA 250X/260X SUPERCHARGER WHEEL BILLET HUB KIT The R&D Supercharger Hub Kit will replace the O.E.M.’s vulnerable part with a redesigned and beefed up precision CNC Machined 6061 billet aluminum part that is much stronger than stock. The new R&D design also offers pulley wheel alignment adjustments with a CNC machined Shim Kit that allows for precision serpentine belt cog alignment. The R&D kit comes complete with a special tool that will indicate the perfect alignment of the crank drive and compressor pulleys. At 8,000 RPM, horsepower and belt life can be greatly sacrificed through misaligned pulleys! The R&D kit offers superior strength, precision pulley alignment, and extended serpentine belt life. Description Part No. A & B. R&D Ultra 250X/260X 611-25001 Supercharger Wheel Hub Kit B. R&D Pulley Alignment Tool Only 611-26000 R&D ULTRA 250X/260X SUPERCHARGER PULLEYS The new R&D Racing Supercharger Pulley Wheel will deliver a noticeable and impressive boost in torque and overall horsepower. Designed and manufactured from high quality billet aluminum and precision hard anodized for superior belt wear resistance. The R&D Pulley is 3/4 lb lighter than the O.E.M. steel pulley, and delivers 2.5 to 3.5 lbs of additional boost pressure along with 30 horsepower. The holeshot acceleration is a solid 1.5-2 boat lengths over stock with a top speed gain of 1 to 2 mph over stock. The R&D Pulley comes completely assembled with a new high performance bearing, all necessary hardware and installation instructions. R&D strongly recommends the use of the R&D Powershot Fuel Tuner, R&D High Output Fuel Injectors and High Volume Fuel Pump Kit to increase fuel flow delivery when using the R&D Supercharger Wheel. Not using these recommended parts can result in engine damage due to a lean air fuel ratio. Description Part No. R&D Supercharger Pulley Wheel 1 to 1 (entry level) 611-25011 R&D Supercharger Pulley Wheel 1.05 to 1 611-25105 R&D Supercharger Pulley Wheel 1.1 to 1 611-25110 OEM Replacement Supercharger Pulley 611-25010 R&D ULTRA 250X/260X SUPERCHARGER BELT TENSIONER WHEEL R&D has significantly improved the Ultra 250X’s serpentine belt tensioning wheel system by redesigning and precision machining a new tensioner wheel with a larger O.D. The new R&D Tensioner Wheel offers a wider adjustment range and helps to reduce belt slippage via more surface area for belt contact. Wheel comes complete with precision bearing installed. Description Part No. R&D Ultra 250X/260X 611-25000 Supercharger Belt Tensioner Wheel ULTRA 250X/260X BEARING REBUILD KIT R&D recommends the inspection of the R&D Supercharger and Tensioner wheel bearings after 15 hours and replacing them after 20 hours. * For the use of R&D supercharger pulleys and tensioner wheel only. Description Part No. R&D Ultra 250X/260X Bearing Rebuild Kit 611-25009 A B