2016 Hot Products Catalog

330 INTAKE SYSTEMS FOUR STROKE ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL ©2016 Hot Products. All rights reserved. Orders & Info: 858-453-4454 • HotProductsUSA.com LAST MINUTE NEW PRODUCTS Description Part No. V-2 Blaster Race Hull BUL-K1105-2 Description Part No. V-2 Wide Body Hydrospace Hull BUL-H1101-2 Bullett Racing V2 Blaster Race Hull In just 2 years of competition, the Bullett Racing V2 Blaster Hull has won 2 World Titles as well as the Jettribe Westcoast Nationals. The Bullett Racing Blaster Hull utilizes the stock seat and hood components from a Yamaha B1 Blaster. In addition to those parts, we also use the OEM gas tank, and that’s where it stops. The hull is ready to be equipped with a Kawasaki 1100 power plant and propulsion system. Bullett Racing has proven time and time again that if you want to be on the podium, you are going to need a Bullett Racing Race Hull. No internet propaganda, just race-proven results! Includes: Top Deck, Bottom Hull, Hood, Hood Skin, Carbon Hull Extensions, Molded-in Tubbies, Ride Plate, Pump Shoe, Intake Grate, Drive Shaft, Dual Cooling Lines, Trim Cable Tube, 2.5” Exhaust. Hulls are pre-drilled for Motor Mounts, Carrier Bearing, Pump, Gas Cap, Hood and Seat Hardware, and Drain Plugs. Gas Tank and Water Box Tabs are also installed. HULL SPECIFICATIONS Design Purpose: Racing and Recreational Hull Weight : 105 Hull Length: 96” Hull Width: 35” HULL OPTIONS Material Options: Fiberglass with epoxy resin for weight saving is standard. Carbon Fiber is an option for an additional cost. Color Options: Black and White Standard, Metal Flake Colors are optional with an additional cost. Graphics Included: The Bullett Racing Graphic Kits are optional with an additional cost. Matting Included: Pre-Installed Jettrim Mats are optional with an additional cost. Intended Fuel Tank: Standard Kawasaki OEM SXR Fuel Tank Intended Intake Grate: Bullett Racing Single Bar Intake Grate Intended Ride Plate: Bullett Racing Carbon Fiber Ride Plate Scupper Valve: Pre-Drilled Trim Tube: Yes Number of Cooling Lines: 2 Exhaust Size: 2.5” ENGINE AND PUMP SPECIFICATIONS Engine Size Range Accepted: Kawasaki 800/1100 Pump Size Range Accepted: Kawasaki 140mm – 145mm Bullett Racing V2 Hydro Race Hull The Bullett Racing V2-WideBoy Hydrospace with molded tubbies has the same look as the original Hydrospace, with the exception of the bottom. The bottom on the V2 is a race-bred and proven design that has been winning championships over the past few years on every continent. This hull was built around the intake system of the boat, with no compromises in race conditions. Bullett Racing only uses the highest quality materials on the market, all of our composite products are built with AME 6000 Pure Epoxy Vinyl Ester Resins. The hull comes with a composite deck and bottom, composite bulkhead, carbon fiber ride plate for rigidity and memory retention, Bullett Racing proprietary intake system (with intake shoe and intake grate), and composite hood (with four air intake tubes, tucked high up in the hood – making it the most water-tight hood on the market). The hull also comes with front and rear bow eyes, 2.5” exhaust, hull extensions, bond flange wedges, steering cable tube, two 1/2” water lines, 5/8” trim cable tube, and motor mount holes pre-drilled for either Hydrospace configuration. Deck and bottom are glued together with a high strength bonding glue, and all hulls are pre-finished on the inside with white gel-coat and black splatter. Bullett Racing has proven time and time again that if you want to be on the podium, you’re going to need a Bullett Racing Race Hull. No internet propaganda, just race-proven results! Includes: Top Deck, Bottom Hull, Hood, Carbon Nose Cowl, Carbon Hull Extensions, Ride Plate, Pump Shoe, Intake Grate, Drive Shaft, Dual Cooling Lines, Trim Cable Tube, 2.5” Exhaust. Hulls are pre-drilled for Motor Mounts, Carrier Bearing, Pump, Gas Cap, Handle Pole Bracket, and Drain Plugs. Gas Tank and Water Box Tabs are also installed. HULL SPECIFICATIONS Design Purpose: Racing and Recreational Hull Weight : 105 Hull Length: 96” Hull Width: 35” HULL OPTIONS Material Options: Fiberglass with epoxy resin for weight saving is standard. Carbon Fiber is an option for an additional cost. Color Options: Black and White Standard, Metal Flake Colors are optional with an additional cost. Graphics Included: The Bullett Racing Graphic kits are optional with an additional cost. Matting Included: Pre-Installed Jettrim Mats are optional with an additional cost. Intended Fuel Tank: Standard Hydrospace Fuel Tank Intended Intake Grate: Bullett Racing Single Bar Intake Grate Intended Ride Plate: Bullett Racing Carbon Fiber Ride Plate Scupper Valve: Pre-Drilled Trim Tube: Yes Number of Cooling Lines: 2 Exhaust Size: 2.5” ENGINE AND PUMP SPECIFICATIONS Engine Size Range Accepted: Webber Motor Pump Size Range Accepted: Hydrospace 140mm – 145mm