2016 Hot Products Catalog

91 ENGINE CONVERSION INTAKE SYSTEMS ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL ©2016 Hot Products. All rights reserved. HotProductsUSA.com • Orders & Info: 858-453-4454 BULLETT RACING CARBON FIBER NOSE COWL Description Part No. Carbon Fiber Nose Cowl SXR-003 for 800 SXR & Bullett Hull BULLETT RACING CARBON FIBER RIDE PLATE Bullett’s ride plate will improve overall speed & handling of your water-craft making your riding experience the best possible. Carbon compressed molded to retain the plate shape and design and not bend like aluminum ride plates. Improves lean angle, straight line tracking and overall grip Description Part No. 800 SXR Carbon Fiber Ride Plate RP-KAW SuperJet 08+ Carbon Fiber Ride Plate RP-YAM+08 BULLETT RACING BEARING KEEPER K1100/1200 Bullett Racing bearing keeper was designed for high RPM output 1100/1200 Kawasaki engines. The keeper is to keep the front bearing in place and not push out the front seal on the flywheel side of the cases. Description Part No. Bearing Keeper K1100/1200 BUL-K1301 JETTRIM MAT SET Description Part No. Bullett V2 Mat Set B101 Bullett Hydrospace Mat Set B102 Bullett Wave Blaster Mat Set B103 BULLETT RACING LIGHTWEIGHT SXR HOOD Bullett’s lightweight SXR hood is extremely strong and very durable all while coming in 12lbs lighter than a OEM Kawasaki SXR hood. The hood is predrilled for installation of the OEM hardware and utilizes the OEM hood seal. Feature additional clearance for installation of a Factory Pipe. Gloss gel coated finish. Description Part No. Lightweight SXR Hood-Black HOOD-KB-BLK Lightweight SXR Hood-White HOOD-KB-WHT BULLETT RACING V2 RACE HULL The Bullett Racing V2 WideBoy Hull is the winningest hull in recent years, in just 4 years Bullett Racing has collected every championship that they have raced in. 3 Kings Cups, 8 World Titles, 4 US National Championships, 3 European Championships, and countless other series championships. Bullett Racing has proven time and time again that if you want to be on the podium you are going to need a Bullett Racing Race Hull. No internet propaganda just race proven results!! This hull was built around the intake system of this boat with no compromises in race conditions. Bullett Racing only uses the highest quality materials on the market; all of our composite products are built with AME 6000 Pure Epoxy Vinyl Ester resins. The hull comes with a composite deck and bottom, composite bulkhead, carbon fiber ride plate for rigidity and memory retention, Bullett racing proprietary intake tubes inside the hood, tucked high up in the hood making it the most water tight hood on the market. The hull also comes with bow eyes front and rear, 2.5 inch exhaust, hull extensions, bond flange wedges, steering cable tube, 2 each 1/2” water lines, 5/8” trim cables tube, motor mount holes pre-drilled for either 800 or 1100 motor configuration, and last of all the deck and bottom are glued together with a high strength bonding glue, and all hulls are pre-finished on the inside with white gel-coat and black splatter. Includes: Top Deck, Bottom Hull, Hood, Carbon Nose Cowl, Carbon Hull Extensions, Ride Plate, Pump Shoe, Intake Grate, Drive Shaft, dual cooling lines, trim cable tube, 2.5” exhaust. Hulls are pre-drilled for Motor Mounts, Carrier Bearing, Pump, Gas Cap, Handle Pole Bracket, and drain plugs. Gas Tank and water box tabs are also installed. Hull Options Material Options: Fiberglass is with epoxy resin for weight saving is standard. Carbon Fiber is an option for an additional cost. Color Options: Black and White Standard, Metal Flake Colors are option with an additional cost. Graphics Included: The Bullett Racing Graphic kits are optional Matting Included: Pre-Installed Jettrim Mats are optional Intended Fuel Tank: Standard Kawasaki OEM SXR Fuel Tank Intended Intake Grate: Bullett Racing Single bar intake grate Intended Ride Plate: Bullett Racing Carbon Fiber Ride Plate Scupper Valve: Pre-Drilled Trim Tube: Yes Number of Cooling Lines: 2 Exhaust Size: 2.5” Description Part No. V2 Race Hull Wideboy Deck BUL-K1102-2 X-2 Sport Hull with V2 Bottom BUL-K1103-2 Hydrospace Hull w/ V2Wideboy MoldedTubbies BUL-H1101-2 Wave Blaster V2 Hull BUL-K1105-2 * See page 330 for more information on V2 Blaster Hull and V2 Widebody Hydrospace Hull