2017 Hot Products Catalog

22 ©2017 Hot Products. All rights reserved. INTAKE SYSTEMS SEA-DOO 4 STROKE ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE CHEMICAL Orders & Info: 858-453-4454 • HotProductsUSA.com Sea-Doo Spark Parts & Accessories are now in the new Sea-Doo Spark feature section pages 8-13 SEA-DOO 4-STROKE • THERMOSTAT • EXHAUST WORX RACING SEA-DOO 4-TEC THERMOSTAT • 160˚F thermostat a direct drop-in replacement for OEM unit in Sea-Doo 4-Tec models • Lowers engine temperatures up to 30˚F • A must for any modified Sea-Doo engine that retains OEM cooling system operating under high load or in hotter climates Description Part No. Sea-Doo 4-Tec Thermostat WR04037 RIVA RXP/RXT/GTX THERMOSTAT KIT RIVA’s cool running Thermostat Kit reduces the operating temperature of your modified 4-Tec ® engine by 30°F for maximum reliability and perform- ance. Kit includes replacement thermostat, billet coolant inlet flange, stock thermostat removal tool, Oetiker ® clamps, Oetiker ® pliers and detailed instal- lation instructions. *NOTE: Thermostat housing (shown above) not included. Description Part No. RIVA Thermostat Kit, SD RXP/RXT/GTX RS1015 R&D SEA-DOO 215/250/260 EXHAUST MANIFOLD X-TENDER/ O2 SENSOR MOUNT KIT The R&D Exhaust X-Tender Kit allows the exhaust to be extended 2 inches which will move the water muffler back 2 inches creating enough room to be able to change out a supercharger (Hot) in 5 minutes. No more hassling with extremely hot exhaust pipes, water mufflers and V-band clamps! An additional bonus is the oxygen sensor mount incorporated into the X-Tender, allowing quick and easy installation of an AFR Gauge (Air/Fuel Ratio) for properly tuning the X power plant. The X-Tender kit installs easily using an additional OEM V-band clamp. The R&D kit will install directly to all Sea-Doo X super- charged models using O.E.M. BRP hardware.You will need to purchase an extra OEM V band clamp. One is not provided. Description Part No. R&D Exhaust Manifold X-Tender/O2 Sensor 333-80155 Mount Kit for Sea-Doo 215/250/260/ 300 R&D Manifold Exh X Tender Kit RXP, RXT 215HP 613-95004 RIVA REAR EXHAUST OUTLET KIT FOR AFTERMARKET INTERCOOLER OR WATERBOX Description Part No. RIVA Rear Exhaust Outlet Kit SD 215/255 Models RS15050-ET RIVA Rear Exhaust Outlet Kit RS15090-ET SD RXT/GTX (S3) and RXP-X (T3) iControl Models* *S3, T3 Models, please check Hull List on page 36 RIVA PRO SERIES SEA-DOO S3/T3 WATER BOX Applications: 2012 & Newer Sea-Doo RXP-X (T3) Models 2009 & Newer Sea-Doo RXT/GTX iControl (S3) Models Important: The following additional RIVA Exhaust Components are required to complete the installation. • RXT/GTX (S3) iControl Models: Aluminum Exhaust Tube RS16091-ET-100 • RXP-X (T3) iControl Models: Aluminum Exhaust Tube RS16091-ET-110 • All S3 & T3 Models: Billet Rear Exhaust Outlet RS15090-ET Note: Water Box is not designed or intended to be used with stock rubber exhaust hose and/or stock exhaust outlet. Note: RS15090-RSB is required for iS/aS SE models. Not required for RXP-X 260 (T3) as there are no storage compartments at rear of craft. Description Part No. RIVA Sea-Doo S3/T3, GTR 215 Models Water Box RS16091 RIVA Rear Storage Bucket RS15090-RSB RIVA WATER BOX RXP-X 300/RXT-X 300 Our Pro-Series Sea-Doo Water Boxes deliver increased horsepower and per- formance by reducing exhaust restriction and back pressure. Developed on a flow bench, our water boxes feature radiused exhaust tubes and end caps for optimum exhaust flow. Innovative short design allows easy servicing of super- charger without removal of exhaust system. High strength aluminum con- struction & precision welds will survive backfires & overheating. Powder coated to prevent corrosion. Includes detailed installation instructions. Description Part No. RXP-X/RXT-X 300, GTX LTD 300 RS16141