221
FOUR
STROKE
INTAKE
SYSTEMS
ENGINE/
GASKETS
EXHAUST
DRIVE LINE
HANDLING
ELECTRICAL WATERLINE
/BILGE
STEERING
& CONTROLS
BODY
ACCESSORIES
SERVICE TOOLS
/HARDWARE
CHEMICAL
©2017 Hot Products. All rights reserved.
HotProductsUSA.com • Orders & Info: 858-453-4454
4253
MSD YAMAHA 650/701 ENHANCER
At lower rpm you’ll notice incredible acceleration and throttle response due
to advancing the timing. Then as the rpm increases, the timing is retarded to
the factory setting to prevent detonation and engine damage. For racers,
there is also a lower rpm limit that you can activate for quick and consistent
holeshots. Everything you need to install the Yamaha Enhancer is supplied
along with factory connectors for a direct plug-in installation!
Not compatible withYamaha 760 engine applications.
Description
Part No.
Yamaha 650/701
4253
MSD SEA-DOO 800
ENHANCER
The Enhancer Ignition for the Sea-Doo
®
800
(also the ‘95, ‘96, XP and GSX) uses a high
speed RISC microprocessor to control all of
the timer and rev limiter functions. This
opens the door for programming, giving you
the ability to set two rev limits and a timing
curve through a series of dip switches built
into the Enhancer. Being able to control the
ignition curve lets you match the timing
specifically to your engine and its modifications. The Digital Enhancer pro-
duces a series of sparks through 3,000 rpm rather than just a single spark.
This feature delivers incredible throttle response, acceleration and keeps the
idle clean and smooth. Note: This modification will eliminate the factory DSS
security system and the handlebar kill feature.
Description
Part No.
Sea-Doo 800 ‘95-96, 97-98 SPX, GTX
4255
MSD STOCK IMPROVED COIL
Replace your old factory coil with this direct bolt-on.
• Replaces Stock kawasaki & Yamaha Coils
• Molded -In 8.5mm Super Conductor Wires
• Output Voltage - 30KV • Primary Resistance - .08 OHM
• Secondary Resistance - 2K OHMS
• Used with Enhancer Ignition for Yamaha 650/701
and Kawasaki 750 only
Description
Part No.
Stock Improved Coil for Start-Up
4294
C57 RACING PRODUCTS
ELECTRIC BOX & BRACKET
A cast aluminum water-tight enclosure for all of your electrical components
when building your SXR 1100, or other skis. Powder-coated for corrosion
resistance in the marine environment. Includes 8 cable glands, rubber
gasket, 6 stainless screws, and a hardware kit for installing Kawasaki 1100
electrical components.
Stainless Steel Bracket for holding Part #C57301 in Kawasaki SXR based
models. Attaches to hood latch studs and bearing carrier bolts.
Description
Part No.
Cast Aluminum Electric Box for SXR1100
C57301
Stainless Steel Bracket for C57301
C57302
JUDGE MOTOR SPORTS
BRACKET FOR ELECTRIC
BOX FOR SXR 1100
Description
Part No.
Electric Box Bracket Front Fuel Tank Side
JMS002
4255
C57301
C57302
THRUST INNOVATIONS
MSD START/STOP MODULE
The Thrust Innovations module terminates the need for a toggle switch
to power off your MSD Total Loss Ignition. Easy to install instructions
with picture diagram included.
Waterproof module that will allow your OEM start/stop switch to function
just like it was meant to, while running Total Loss, without the need for
an additional switch.
• Starts just like OEM (only when lanyard is attached)
• Kills motor and powers down Total Loss once lanyard is removed or
“STOP” button is touched momentarily
• Does not draw from battery, will not cause battery drain
• Sealed and potted to ensure water resistance and to isolate from shock
• All connections are soldered
• Comes with OEM connections to attach directly to your start/stop switch
Description
Part No.
Total Loss Ignition Start/Stop Module
TI-MSD-TL-MD
