2019 Hot Products Catalog

Orders & Info: 858-453-4454 • HotProductsUSA.com 198 INTAKE SYSTEMS FOUR STROKE ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE INDEX © 2019 Hot Products. All rights reserved. SOLAS STAINLESS STEEL YAMAHA 12-VANE STATOR SECTION Get HUGE gains in Hook Up on bottom end, and overall efficiency in rough con- ditions, and jet wash! This pump is a must have for Freestyle! The Brand New Solas Yamaha 144mm 12 Vane Pump Stator is now available and is an incredible value for the HUGE performance gain resulting from bolting this pump on! This is the stator section only, is stainless steel, with large diameter bearing carrier, and a 12 vane standard position design. It replaces the stock Yamaha 144mm 6 vane aluminum stator section. No need to buy an expensive extended shaft with this pump conversion. You will need a large hub design impeller such as the Impros Hooker impeller, the Solas Concord YQ-CD, or Skat-Trak C+75 Swirl impeller with this pump. Solas 2016 YQS-SV-144/74 Production Update: The new production of the Solas 144 Yamaha stator have been updated so that it is no longer required to use a Impros Pump Spacer Ring part# IMYQ-NS. The pump sealing ring on the rear of the 2016 Solas 144 Yamaha stator has been widened to 6.61mm wide, Hot Products recommend you seal the stator section to the reduction nozzle using 1 Minute Gasket, Right Stuff or a similar product to prevent any possible leaking when the pump is under pressure. The 2015 and earlier Solas 144 Yamaha stator has a 3.00mm pump sealing ring on the rear of the stator section, if you have a stator from this production it will require the use of a Impros Pump Spacer Ring part# IMYQ-NS. Solas 144 Yamaha Parts Part No. Stainless Steel Yamaha 12-Vane 144mm Stator YQS-SV-144/74 Stainless Steel Yamaha 144mm Pump Housing YBS-HS-144 A. Impros 144mm Pump Spacer IMYQ-NS (See production update detailed above) B. Impros Freestyle Tail Cone IMYQ-FC WSM Yamaha Pump Bearing & Seal Kit 003-630 Solas 148 Yamaha Parts Part No. Stainless Steel Yamaha 12-Vane 148mm Stator YRS-SV-148/74 Stainless Steel Yamaha 148mm Pump Housing YRS-HS-148 WSM Yamaha Pump Bearing & Seal Kit 003-630 Solas Impeller for 148mm Housing Part No. Concord 9/15 YRS-CD-09/15 Concord 12/18 YRS-CD-12/18 Concord 13/19 YRS-CD-13/19 Concord 14/20 YRS-CD-14/20 See page 219 for additional Solas Stators and Pump Housings. A. B. Pump Housing 08-KPS SOLAS COMPLETE 140mm PUMP ASSEMBLY FOR HYDROSPACE S4 Description Part No. 140mm Pump Assembly for Hydrospace S4 HS-PM-140/74T YAMAHA PUMP SEALS Fits both OEM Yamaha, Skat-Trak Billet Magnum Pumps and Torrent Pumps. Description Pump Size Part No. Thrust Innovations Yam Pump Seal 155mm TI-155-PMP-SL Genuine Yamaha Pump Seal 144mm 6R7511170100 SOLAS 140MM - 12-VANE PERFORMANCE PUMP FOR KAWASAKI The Solas Kawasaki High Performance 12 Vane Pump is a stainless steel vane, 140mm diameter with 75mm bearing carrier, pressed into an aluminum housing. It is a "Standard Position" pump, meaning, it is not set back, and you can use your existing driveshaft (no extended shaft necessary). It comes complete with bearings, seals, pump shaft, and tail cone and to top it off, an adjustable diameter drop nozzle system! The pump fits the 2003-2012 Kawasaki 800 SXR. It also fits the 1992-2002 750 models SX, SXi, SXi Pro, SS, ST, Xi, and XiR. This pump kit does not include an impeller, trim system cable, or lever, we suggest using either the Solas KP-DF impeller, or the Skat-Trak C-75 Magnum Swirl impeller. These pumps really improve rough water performance, and they fit right up to the hull like an OEM pump. Description Part No. Solas 140mm - 12 Vane Performance KPS-PM-140/74T* Pump with Trim System for Kawasaki Solas 140mm - 12 Vane Performance Pump 08-KPS Seal and Bearing Kit Solas Kawasaki Trim System Only KPS-NZ-140/74T* Skat-Trak Trim Cable for Solas Pump/Trim PRSTKAWSXRT *Trim levers are not included with these Solas items, see page 269