2019 Hot Products Catalog

JET WORKS QUICK DISCONNECT WATER RESTRICTOR QD-38 comes with 4/3/2mm restrictor inserts used for controlling water flow through exit passes, stinger, head pipes, etc. QD-14 is for use with Mikuni Jets (not included), and allows quick change in small increments of water flow. Description Part No. D. Quick Disconnect Wtr Restrictor 1/4” QD-14 E. Quick Disconnect Wtr Restrictor 3/8” QD-38 HIGH SPEED INDUSTRIES 3/8” INLINE WATER RESTRICTOR This simple water restrictor installs inside of your 3/8” cooling line. The restrictor is designed to accept a Mikuni main jet (N102.221-SIZE) to control the flow of water. This small restrictor is ideal for exhaust stingers and it works great with a flow control valve. Description Part No. 3/8” Inline Water Restrictor HSI05 *Mikuni main jets are sold separately JET WORKS FLOW CONTROL VALVE The Flow Control Valve provides improved throttle response and much quicker starts by drying out your waterbox at low rpm and idle speeds. Tests have shown an average acceleration improvement of 10 feet over a non-equipped model in the first 50 feet. The Flow Control Valve allows unrestricted water flow to the Stinger for better top speed.Yet it controls the amount of water at low speeds for better response. It also allows for an easier tuning of the Carburetors. It does not interfere with normal engine or exhaust pipe cooling and is compatible with all electronic water injection systems. Race Legal for All Classes. Two Models are available. Both are adjustable. The Standard Flow Control Valve is preset at 3.5 p.s.i. and is adjusted by adding the supplied stainless steel shims to increase the spring tension. The Pro-Series is externally adjustable by turning the outer housing by hand. Pressure can be tested with pop off gauge. All PWC w/OEM or aftermarket exhaust systems (except Yamaha’s w/OEM exhaust) Description Part No. A. Standard Flow Control Valve 3/8” 52-3118 B. Pro Flow Control Valve 3/8” 52-3119 C. Pro Flow Control Valve 1/4” 52-3122 HotProductsUSA.com • Orders & Info: 858-453-4454 249 FOUR STROKE INTAKE SYSTEMS ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE INDEX © 2019 Hot Products. All rights reserved. E. D. JET WORKS ADJUSTABLE WATER RESTRICTOR Allows user to adjust flow on any 3/8” ID waterline. A great product for fine tuning engine/exhaust temperature for maximum power. Description Part No. Adjustable Water Restrictor 3/8” JWR-01 PJS PRO FLOW COOLING WATER CONTROL VALVE PJS’s knurled gripping surface on the outside of both elements for easy adjusting on all 3/8” ID waterline. The inner workings are constructed using stainless steel and corrosion proof Delrin nylon for years of trouble free service. The PJS Pro Flow is designed with an extra long length extended range of operation for a broad range of opening pressures to allow tuners to find that perfect "sweet spot" no matter how low or high you need it to be. Description Part No. PJS Pro Flow Control Valve EX-00100 A . C . B. RHAAS 3 WAY WATER OUTLET Water outlet plate for all watercraft. Has 3 water outlets in one billet plate. Use 1/8 NPT fittings on the backside to make them fit any hose size.You can even block one with a plug and run 2 water outlets. Made from billet 6061 aluminum and clear anodized for protection from the elements. Comes with installation hardware as well. Available in 2 styles: fan spray pattern, and 90 degree pattern 3 Way Water Outlet Part No. A. Fan spray pattern 3WAYWO-FAN 90 degree pattern 3WAYWO-90 Star and STAROUTLET Stripes 3 Water Outlet RHAAS 4 WAY WATER OUTLET Water outlet plate for all watercraft. Has 4 water outlets in one billet plate. Use 1/8 NPT fittings on the backside to make them fit any hose size.You can even block one with a plug and run 3 water outlets. Made from billet 6061 aluminum and clear anodized for protection from the elements. Comes with installation hardware as well. Description Part No. 4 Way Water Outlet 4WAYWO HIGH SPEED INDUSTRIES BILLET WATER MANIFOLDS These billet water manifolds are ideal for high horsepower applications. All manifolds are machined from billet aluminum and are anodized for corrosion resistance. Every manifold has 2 - 1/4" NPT inlet ports and 4, 6, or 8 - 1/8" NPT outlet ports. Simply epoxy the manifold to your hull or use the mounting holes for installation. Water Manifold Part No. 4 Port 5.25” x 1” x 1” HSI06 6 Port 4.75” x 1” x 1” HSI07 8 Port 6.25” x 1” x 1” HSI08 A .