2019 Hot Products Catalog

HotProductsUSA.com • Orders & Info: 858-453-4454 57 YAMAHA 4 STROKE INTAKE SYSTEMS ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE INDEX © 2019 Hot Products. All rights reserved. YAMAHA • CONTROL • PUMP SOLAS STAINLESS STEEL YAMAHA 12-VANE STATOR SECTION Pump Size Hub Size Part No. 160mm 74mm YSS -SV-160/74 (SHO only, small water cooling outlet) 160mm 74mm YVS -SV-160/74 (SVHO, SHO & GP1800 larger water cooling outlet) SOLAS STAINLESS STEEL YAMAHA PUMP HOUSING Pump Size Part No. Solas 155mm Wear Ring Housing YFS-HS-155 Solas 160mm Wear Ring Housing YVS-HS-160 YSS-SV-160/74 YVS-SV-160-74 YVS-HS-160 YFS-HS-155 R&D LOW FRICTION DUAL WASHER IMPELLER SPACER FOR YAMAHA 2008+ The R&D “Dual Washer” Impeller Spacer Kit for Yamaha replaces the OEM single seal washer with a specifically designed and machined kit that incorpo- rates a second low friction slip washer to be used, allowing impellers to be removed with 50 percent less torque during the impeller removal process! Tired of impellers that are so galled up that they have to be machined or cut off? Tired of broken impeller tools and broken vises? Install the R&D low fric- tion “Dual Washer” Kit and impeller removal will be super easy when making impeller changes. Many SVHO owners have had these issues and have had to cut up and throw away impellers and repair damaged threads. The R&D kit puts an end to all the expensive repairs and downtime from these issues. The R&D “Dual Washer” Kit fits all Yamaha models both supercharged and N.A. from 2008 and up! Description Part No. R&D “Dual Washer” Impeller Spacer Washer Kit 132-81111 IMPELLER SHAFT HOLDER TOOL Description Part No. FX-SHO/FZR/FZS/VXR/VXS TOOL #53 20mm Splined Impeller Tool SKAT-TRAK MID SHAFT WRENCH This new Skat-Trak tool will insert a Yamaha mid shaft and allow you to hold it while removing the coupler, without damaging the shaft. Description Part No. 20mm Mid Shaft Wrench RWRYAMMS R&D RACING CAVITATION FIGHTER PUMP SLEEVE FOR 2014+ YAMAHA SVHO MODELS The R&D Cavitation Fighter Pump Sleeve eliminates the “square edge” transition between the transom plate (155mm id.) and the pump liner (160mm id) . The Cav-Fighter Sleeve installs between the two stock parts to blueprint a ramp transition from the transom to the pump liner. When water gets pulled into the pump, the water boils (cavitates) as the impellor is only a half inch (.500”) from the square edge. Field testing con- firmed by eliminating the square edge the Cav-Fighter Sleeve reduced cavita- tion on holeshot acceleration and in hard turns. NOTE: Do not use with stock Solas prop Part # YV-CD 13/18. This prop requires setback modifications of .120” to clear sleeve. Description Part No. Cavitation Fighter Pump Sleeve 132-80160 for 2014+ Yamaha SVHO WORX BILLET ENGINE COUPLER SET • Billet Drive Coupler for Yamaha 1.8 Engine • Billet construction huge strength upgrade over stock cast unit • Utilizes OEM rubber coupler dampner • A must have for any high horsepower/race watercraft Description Part No. Fits all 1.8 Yamaha Engines (Sold in pairs) WR04003 2018 IJSBA B LOWSION W ORLD F INALS IN L AKE H AVASU C ITY , AZ. P HOTO COURTESY OF J IN O MURA .