Hot Products 2020 Catlog

Orders & Info: 858-453-4454 • HotProductsUSA.com 126 INTAKE SYSTEMS FOUR STROKE ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE INDEX © 2020 Hot Products. All rights reserved. TRIPLE INTAKE MANIFOLDS FOR MIKUNI CARBURETORS K1100 to GP1200 CARB CONVERSION PLATE Rhaas calls this 44’s on a budget. This plate allows you to run the stock carb racks from a Yamaha GP1200 on a stock Kawasaki 1100 manifold. Upgrade the stock Keihin 1100 carbs with Mikuni 44mm carbs. Kawasaki Part No. Conversion Plate for Kawasaki 1100 1100-GP1200 to use stock GP1200 carb kit K1100 to YAM 1100 CARB CONVERSION PLATE This allows you to convert your stock Kawasaki 900-1100 intake manifold to a speed plate system and converts to 38mm Mikuni carbs from a Yamaha 1100 engine. A huge upgrade from the stock CV carbs. The 38mm Mikuni carbs have a great signal and perform fabulous.. Kawasaki Part No. Conversion Plate for Kawasaki 1100 K1100-Y1100 to use stock Yamaha 1100 carb kit R&D YAMAHA 1100/1200 INTAKE MANIFOLD Fits all Yamaha 1100 and 1200 Non Powervalve Triple motors. Designed to fit all 44mm and 46mm Mikuni carbs. Supplied with all required hardware and gaskets. Yamaha Part No. R&D 1100/1200 (63M/65U) Intake Manifold 232-11000 DASA KAWASAKI 1100/1200 INTAKE MANIFOLD Dasa’s billet intake manifold with speed plate for Mikuni 44mm to 50mm carbs, developed for V-Force 3 reed applications (V3150-794-3). Supplied with all required hardware, gaskets and both a pump and diaphragm throttle cable bracket. Kawasaki Part No. DASA 1100/1200 Billet Intake Manifold V-3 Design KA-1101 Replacement O-Ring (Sold Individually) 137V RHAAS 900-1100 CARB SPEED PLATE ASSEMBLY This allows you to convert your stock Kawasaki 900-1100 intake manifold to a speed plate system and converts to 44mm Mikuni carbs at the same time. Also works on all aftermarket 900-1100 intake manifolds that have 120mm spacing. Only available in 44mm for stock 1100 intake. Available in 44mm, 46m, and 48mm for aftermarket intakes. Description Part No. 44mm for 900-1100 Stock Intake 1100SPDPLT-44STOCK to convert 44mm Mikuni Carb 44mm for Aftermarket Intake 120mm Spacing 1100SPDPLT-44/120 46mm for Aftermarket Intake 120mm Spacing 1100SPDPLT-46/120 48mm for Aftermarket Intake 120mm Spacing 1100SPDPLT-48/120 8MM STAINLESS STEEL STUDS, NUTS, WASHERS & FLANGE NUTS FOR INTAKE MANIFOLD High quality stainless steel hardware for all intake manifolds that utilize 8mm hardware. The flange nuts are the perfect solution to solve the issue of having flat washers and the possibility of dropping them in the engine compartment when removing/installing carburetors. Sold in bags of 10. Description Part No. A. 8 x 30 Stud 62-4030 B. 8mm Nut 63-0008 C. 8mm Flat Washer 63-2008 D. 8mm Flange Nut 63-0008-FLANGE A. B. C. D.