2021 Hot Products Catalog

Orders & Info: 858-453-4454 • HotProductsUSA.com 208 INTAKE SYSTEMS FOUR STROKE ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE INDEX © 2021 Hot Products. All rights reserved. A. Pump Housing 08-KPS SOLAS 140MM - 12-VANE PERFORMANCE PUMP FOR KAWASAKI The Solas Kawasaki High Performance 12 Vane Pump is a stainless steel vane, 140mm diameter with 75mm bearing carrier, pressed into an aluminum housing. It is a "Standard Position" pump, meaning, it is not set back, and you can use your existing driveshaft (no extended shaft necessary). It comes complete with bearings, seals, pump shaft, and tail cone and to top it off, an adjustable diameter drop nozzle system! The pump fits the 2003-2012 Kawasaki 800 SXR. It also fits the 1992-2002 750 models SX, SXi, SXi Pro, SS, ST, Xi, and XiR. This pump kit does not include an impeller, trim system cable, or lever, we suggest using either the Solas KP-DF impeller, or the Skat-Trak C-75 Magnum Swirl impeller. These pumps really improve rough water performance, and they fit right up to the hull like an OEM pump. Description Part No. Solas 140mm - 12 Vane Performance KPS-PM-140/74T* Pump with Trim System for Kawasaki Solas 140mm - 12 Vane Performance Pump 08-KPS Seal and Bearing Kit Solas Kawasaki Trim System Only KPS-NZ-140/74T* Skat-Trak Trim Cable for Solas Pump/Trim PRSTKAWSXRT *Trim levers are not included with Solas pumps, see page 285 WATCON IMPELLER PITCH GUAGES It's a known fact; not all impellers are created equal. Sometimes when impellers are mass pro- duced, there are subtle differences that can affect performance. Use this simple tool to measure the pitch angle and blade length of each blade throughout its circumference. This enables you to make adjust- ments to the pitch where needed. Great for fine tuning, making minor changes or verifying pitch when sending impellers off for repair. Description Part No. 140-142mm Impeller Pitch Guage IMP-142 144-148mm Impeller Pitch Guage IMP-148 155-160mm Impeller Pitch Guage IMP-160 175-177mm Impeller Pitch Guage IMP-177 See page 210 for 165mm Pitch Guage YAMAHA PUMP SEALS Fits both OEM Yamaha, Skat-Trak Billet Magnum Pumps and Torrent Pumps. Yamaha Pump Seal Pump Size Part No. Genuine OEM Yamaha 144mm 6R7511170100 Thrust Innovations 155mm TI-155-PMP-SL Torrent Pumps 144/148 148-PS Torrent Pumps 150/160 155-PS SOLAS STAINLESS STEEL YAMAHA 12-VANE STATOR SECTION Get HUGE gains in Hook Up on bottom end, and overall efficiency in rough condi- tions, and jet wash! This pump is a must have for Freestyle! The Brand New Solas Yamaha 144mm 12 Vane Pump Stator is now available and is an incredible value for the HUGE performance gain resulting from bolting this pump on! This is the stator section only, is stainless steel, with large diameter bearing carrier, and a 12 vane standard position design. It replaces the stock Yamaha 144mm 6 vane aluminum stator section. No need to buy an expensive extended shaft with this pump conversion. You will need a large hub design impeller such as the Impros Hooker impeller, the Solas Concord YQ-CD, or Skat-Trak C+75 Swirl impeller with this pump. Solas 144 Yamaha Parts Part No. Stainless Steel Yamaha 12-Vane 144mm Stator YQS-SV-144/74 Stainless Steel Yamaha 144mm Pump Housing YBS-HS-144 A. Impros Freestyle Tail Cone IMYQ-FC WSM Yamaha Pump Bearing & Seal Kit 003-630 Solas 148 Yamaha Parts Part No. Stainless Steel Yamaha 12-Vane 148mm Stator YRS-SV-148/74 Stainless Steel Yamaha 148mm Pump Housing YRS-HS-148 A. Impros Freestyle Tail Cone IMYQ-FC WSM Yamaha Pump Bearing & Seal Kit 003-630 Solas Impeller for 148mm Housing Part No. Concord 9/15 YRS-CD-09/15 Concord 12/18 YRS-CD-12/18 Concord 13/19 YRS-CD-13/19 Concord 14/20 YRS-CD-14/20 See page 235 for additional Solas Stators and Pump Housings.