2021 Hot Products Catalog

KAWASAKI 650 ELECTRIC BOX PLATE Replaces OEM part 3712-13183. Note: Gray grom- met shown is not included. Description Part No. Kawasaki 650 55-3100 Electric Box Plate Orders & Info: 858-453-4454 • HotProductsUSA.com 246 INTAKE SYSTEMS FOUR STROKE ENGINE/ GASKETS EXHAUST DRIVE LINE HANDLING ELECTRICAL WATERLINE /BILGE STEERING & CONTROLS BODY ACCESSORIES SERVICE TOOLS /HARDWARE INDEX © 2021 Hot Products. All rights reserved. KAWASAKI BATTERY SOLENOID POST Our solenoid post allows placement of corroded post without replacing the expensive solenoid on all Kawasaki Jet Ski with small electrical box. Description Part No. Solenoid Post (2 per set) 55-3350 KAWASAKI ELECTRICAL BOX REPAIR FITTING One kit contains 5 each of the nylon fittings and o-rings. These fittings will work on all Kawasaki watercraft electrical boxes and trim units. Description Part No. Electrical Box Repair Fittings WCW-EBOXFIT (5 sets per pack) ADA BILLET ALUMINUM KAWASAKI ELECTRICAL BOX FITTING, CAP AND PLUG Billet aluminum electric box fittings, caps and plugs replace the stock Kawasaki electric box plastic fittings, caps and plug extra holes. The nut is for mounting and sealing the fitting to a box with no threads. Color Cap (A) Plug (B) Fitting (C) Black 31-252500 31-253000 31-252000 Blue 31-252510 31-253010 31-252010 Red 31-252520 31-253020 31-252020 Orange 31-252525 31-253025 31-252025 Green 31-252535 31-253035 31-252035 Silver 31-252590 31-253090 31-252090 D . E-Box Fitting Backing Nut 31-253590 KAWASAKI ELECTRIC BOX GASKETS Description Part No. D. All 440/550/550SX 51-0440 E. All 650SX 51-0650 D. E. A. CAP C. FITTING D. Nut B. PLUG C57 RACING ELECTRIC BOX & BRACKET A Powder-coated cast aluminum water-tight enclosure for all of your electrical components when building a conversion ski. Includes 8 cable glands, rubber gasket, 6 stainless screws, and a hardware kit for installing Kawasaki 1100 electrical components. Stainless Steel Bracket for holding Part #C57301 in Kawasaki SXR based models. Attaches to hood latch studs and bearing carrier bolts. Description Part No. Cast Aluminum Electric Box for SXR1100 C57301 Stainless Steel Bracket for C57301 C57302 JUDGE MOTORSPORTS BRACKET FOR ELECTRIC BOX FOR SXR 1100 Description Part No. Electric Box Bracket Front Fuel Tank Side JMS002 C57301 C57302 WATCON CONVERSION PLATE K750SS E-BOX TO K550 MOUNT Use when doing a 650, or 750 engine swap into a 440 or 550 hull, and running 750 electrics, and SX driveline (Either SX hull, or Pump swap with X2 driveline). Allows you to mount the Kawasaki 750SS full electric box to a 550 hull. Installation is clean, and looks factory. 750 electrics have a timing curve built into the CDI, and will outperform 650 electrics. AGAIN will NOT fit with JS Driveline. Description Part No. Kaw 750SS E-Box to 550 Mount Conversion Plate AP550-750SS K750 ELECTRONIC BOX CONVERSION TO JS 440/550 HULL Custom made 550/750 Conversion Billet Aluminum E-Box. This E-box fits inside a Kawasaki JS440, JS550, 550SX jet ski hull. Bolts to original JS/SX ebox location and allows the use of K750 electrical without relocating the ebox. This ebox is a 2 piece billet design with oring groove to seal out water Delron black ebox fittings and hardware included. Kawasaki 440/550/550SX Part No. Billet K750 Electronic Box Conversion WCW-750EBOX to JS440/550/550SX Hull Complete assembled electrical box shown for reference only.