2023 Hot Products Catalog

Four Stroke Intake Systems Engine & Gaskets Exhaust Driveline Handling Electrical Waterline & Bilge Cables Steering & Controls Body Accessories Service Tools & Hardware Index ELECTRICAL Orders & Info: 858-453-4454 • HotProductsUSA.com 255 © 2023 Hot Products. All rights reserved. MSD ENHANCERS, PLUG BOOTS & WIRES MSD YAMAHA 650/701 ENHANCER At lower rpm you’ll notice incredible acceleration and throttle response due to advancing the timing. Then as the rpm increases, the timing is retarded to the factory setting to prevent detonation and engine damage. For racers, there is also a lower rpm limit that you can activate for quick and consistent holeshots. Everything you need to install the Yamaha Enhancer is supplied along with factory connectors for a direct plug-in installation! Not compatible withYamaha 760 engine applications. Description Part No. Yamaha 650/701 4253 MSD SEA-DOO 800 ENHANCER The Enhancer Ignition for the Sea-Doo ® 800 (also the ‘95, ‘96, XP and GSX) uses a high speed RISC microprocessor to control all of the timer and rev limiter functions. This opens the door for programming, giving you the ability to set two rev limits and a timing curve through a series of dip switches built into the Enhancer. Being able to control the ignition curve lets you match the timing specifically to your engine and its modifications. The Digital Enhancer produces a series of sparks through 3,000 rpm rather than just a single spark. This feature delivers incredible throttle response, acceleration and keeps the idle clean and smooth. Note: This modification will eliminate the factory DSS security system and the handlebar kill feature. Description Part No. Sea-Doo 800 ‘95-96, 97-98 SPX, GTX 4255 MSD STOCK IMPROVED COIL Replace your old factory coil with this direct bolt-on. • Replaces Stock Kawasaki & Yamaha Coils • Molded -In 8.5mm Super Conductor Wires • Output Voltage - 30KV • Primary Resistance - .08 OHM • Secondary Resistance - 2K OHMS • Used with Enhancer Ignition for Yamaha 650/701 and Kawasaki 750 only Description Part No. MSD Stock Improved Coil 4294 4255 4253 MSD SPARK PLUG BOOT RETAINERS There’s no excuse for losing a race due to a plug wire popping off when you run MSD’s Boot Retainers. These handy clamps are molded from heat resistant nylon material and will lock the boot to the spark plug. Description Part No. Boot Retainer, 90 o Spark Plug Boots & Terminal (2 cyl.) 3340 Boot Retainer, individual piece 15991 MSD SPARK PLUG BOOT & TERMINALS Description Part No. A. MSD 90 o Spark Plug Boots & Terminal (2 cyl.) 3311 A. MSD 90 o Spark Plug Boots & Terminal (3 cyl.) 3311-3 B. MSD Spark Plug Terminals (Pack of 100) 34615 B. MSD Spark Plug Terminals (Pack of 10) 34615-10 A. B. MSD 8.5MM SUPER CONDUCTOR SPARK PLUG WIRE Spark plug wires have two main objectives; transfer the spark energy and suppress the Electro Magnetic interference (EMI) that the spark voltage creates. The MSD 8.5mm Super conductor delivers the best of both worlds. MSD uses a special copper conductor keeping resistance under 50 ohms per foot! Even with this low resistance, the wire retains high EMI suppression capabilities. By wrapping the conductor tightly around a ferro-magnetic impregnated center core and EMI choke is created, keeping any interference inside the wire. Length of each wire is 30” Description Part No. Two Cylinder Wire Set 31009 Three Cylinder Wire Set 31039 Bulk Wire Length Color Part No. 25 Feet Bulk Wire Red 34019 25 Feet Bulk Wire Black 34013 100 Feet Bulk Wire Red 34049 100 Feet Bulk Wire Black 34043 300 Feet Bulk Wire Red 34059 300 Feet Bulk Wire Black 34053 31009 Bulk Wire