Hot Products 2024 Catalog

Index Service Tools & Hardware Accessories Body Steering & Controls Cables Waterline & Bilge Electrical Driveline Handling Exhaust Engine & Gaskets Intake Systems Freestyle Freeride FREESTYLE FREERIDE Orders & Info: 858-453-4454 • HotProductsUSA.com 114 © 2024 Hot Products. All rights reserved. 2 STROKE SUPERJET NEW PRODUCTS TRUE PERFORMANCE ENGINEERING BASE GASKET Description Part No. TPE Base Gasket TP003B TC FREERIDE EXHAUST RISER HOSE Most aftermarket hulls features a rear exhaust that is just a straight tube that does not have a trap to prevent water from pushing back into the exhaust and potentially back into the engine. Taylor Curtis of TC Freeride has developed this high temp silicone hose to create a trap inside the engine compartment without compromising any performance. This is a must for all surf skis. Description Part No. TC Freeride Exhaust Riser Hose TC-EXH-RISER TC FREERIDE EXHAUST ELBOW Taylor Curtis of TC Freeride has developed this high temp silicone elbow to allow for that perfect fitting exhaust and waterbox installation. The elbow features 6” legs on both sides. This elbow is 2 1/2” on one side and 2” on the other. Description Part No. TC Freeride Exhaust Elbow TC-EXH-ELBOW HIGH SPEED INDUSTRIES YAMAHA SHIM KITS HIGH SPEED INDUSTRIES YAMAHA CARB MANIFOLD PLATE HSI-03-0012: Billet carb manifold plate for Yamaha 64X intake manifold. Allows you to adapt dual SBN 44mm carbs and up to 48mm onto the OEM 64X intake manifold. Gasket surface on both sides. Anodized black. *It is recommended to port match the intake manifold for the best performance. HSI-03-0013: Billet carb manifold plate for Yamaha 62T intake manifold. One- piece plate for 38mm carbs. Gasket surface on both sides. Anodized black. Description Part No. Yamaha 64X Carb Manifold Plate HSI-03-0012 Yamaha 62T Carb Manifold Plate HSI-03-0013 *HSI manifold plates include all required hardware. HIGH SPEED YAM 701 HIGH COMPRESSION HEAD GASKET High Speed Industries custom head gasket will decrease your head volume by 2cc’s and will increase compression/performance.. YamahaThickness Type Bore Size Part No. 701 All 0.030 Fiber 82.35mm HSI-88-0034 RHAAS SUPERJET ENGINE SETBACK KIT Setback kit for Superjet twin cylinder motor. This kit allows you to move the motor back 1”-1 1/4”. You can use a custom midshaft to move back 1 1/4” or use a GP760 midshaft and move the motor back 1”. Helps to give the boat a little change in attitude and helps getting the nose up for freestyle. Includes motor plates, motor mounts and all hardware to make the swap. Uses OEM #65V51323-00-00 midshaft. . Description Part No. Superjet Engine Setback Kit SUPERBACK Engine Shim Kit Part No. Engine Shim Kit HSI-95-0033 Includes four of each size: 0.5 mm thick, 1.0 mm thick, and 1.5 mm thick. (12 shims total). Stainless Steel. Pump Shim Kit Part No. Pump Shim Kit HSI-95-0037 Includes two of each size: 0.5 mm thick and 1.0 mm thick. (4 shims total). Stainless Steel. Mid Shaft Shim Kit Part No. Mid Shaft Shim Kit HSI-95-0042 Includes two of each size: 0.5 mm thick and 1.0 mm thick. (4 shims total). Stainless Steel HIGH SPEED IN- DUSTRIES SJ REPLACEMENT PERFORMANCE 38MM CARB KIT Do you have salty dual 38mm carbs that are too far gone? Or are your SJ carbs old, tired, and you're tired of chasing your tail to get them running right? We have a solution for you. H.S.I. BUILT - Genuine Mikuni 38mm SBN perform- ance carbs pre-assembled to be an OEM SBN 38 duplicate with better per- formance. Bolt on in replacement of your OEM carbs. * Includes: Primer fittings, carb support rail, billet throttle drum, coupler linkage kit, billet carb manifold plate, and needed gaskets. NOTE:You may still need air filter adapters and flame arrestor filter. These carbs are jetted for a 61x/62t 701cc engine with stock 61x exhaust and tornado style air filters. WARNING - Go up a full 2 sizes on the main jet for a b-pipe application" Description Part No. SJ Replacement Performance 38mm Carb Kit HSI-SJ-CARBKIT *This carb kit is not IJSBA Lites class race legal.