Hot Products 2024 Catalog

Index Service Tools & Hardware Accessories Body Steering & Controls Cables Waterline & Bilge Electrical Driveline & Handling Exhaust Engine & Gaskets Intake Systems Four Stroke DRIVELINE & HANDLING Orders & Info: 858-453-4454 • HotProductsUSA.com 234 © 2024 Hot Products. All rights reserved. PUMP SHOES & PUMP STUFFERS 144/155/160 PUMP SHOES See Freestyle section for information. Description Part No. Yamaha 144 Pump Shoe (Plastic) PM-SH-PLAS-144 Yamaha 155 Pump Shoe (Aluminum) PM-SH-AL-155 Yamaha 160 Pump Shoe (Aluminum) PM-SH-AL-160 BLOWSION YAMAHA ALUMINUM PUMP SHOES Aluminum pump shoes are designed to replace the stock plastic unit which is prone to fail with a winged intake grate. These aluminum pump shoes have a completely redesigned front entrance compared to the OEM plastic pump shoe allowing water to feed into the pump more efficiently. Improves hookup, cornering, stability, rough water speed and overall handling. Blowsion Pump Shoe - these pump shoes will require the 4 mounting holes for the hull be drilled and the 2 intake grate rear mounting holes be drilled and tapped. Minimal fitting of the pump shoe to the hull is required. Yamaha 144 Pump Shoe Part No. Blowsion SuperJet (All), Waveblaster (Aluminum) 02-02-432 Yamaha 148 Pump Shoe Blowsion Yamaha 148mm (Aluminum) 02-02-434 WORX RACING YAMAHA ALUMINUM PUMP SHOES WORX Racing cast aluminum pump shoe is a direct replacement for the stock plastic pump shoe that easily distorts and breaks under high speeds in race applications or under huge load from freestyle engines. Pre-drilled and tapped for easy installation this is a must have upgrade for your modified stand up to allow use of large-winged aftermarket intake grates that provide maximum efficiency to your jet pump without sacrificing reliability. Suits all Yamaha SuperJets and most aftermarket hulls. Yamaha 144 Pump Shoe Part No. WORX SuperJet (All), Waveblaster (Aluminum) WR06009 Yamaha 148 Pump Shoe WORX Yamaha 148mm (Aluminum) WR06009-148 A. B. C. PROWATERCRAFT YAMAHA 144 PUMP SHOE Prowatercraft cuts back the “shoe shape” to open up the intake to improve cavitation and hook up. Because, one of the more noticeable issues with the older Yamaha Super Jet and Yamaha Wave blaster is cavitation in the turns when the ski is re- ally leaned over. The pump shoe is the best way to adjust this issue. The opening is 144mm to fit the stock Yamaha pump. Prowatercraft has strong in- serts that will exceed stock expectations. Another advantage is the deeper shoe shape, which will scoop more water and create a even flow to most in- take grates available. Description Part No. Yamaha 144 Pump Shoe (HFC) PW-03-630 PROWATERCRAFT PUMP STUFFERS Intake pump cavity stuffer design to fill in the space air gets trapped for reduced cavitation and better drive. Kawasaki Part No. A. K440/550 PW-550-620 B. K650SX/X2 PW-650-620 C. K750SX/SXI (not SXI Pro) PW-750-620 K750SXI PRO PW-01-620 SXR 800/1100 PW-01-621 D. 1500 SX-R PW-01F-620 SC/JL650 PW-01SC-620 Yamaha Part No. E. Wave Blaster 1 PW-WB-620 F. Square Nose SuperJet PW-03-620-SJ1 Sea Doo Part No. Spark PW-04S-620 D. E. F.